Binding machine structure picture
Model: BBM-04
Display Screen Show
- Product functions
- Instant heat:
No warm-boot, open then can direct use
- Easy to operate:
Please put the notes vertically into Entrance, then automatically finished the action
- Show function:
Chinese, English shows for global, The machine
Functions, failure at a glance, users can exclude
Their operation, Reduce the probability of repair,
Improve user productivity.
- Set up a simple:
Demand on the heating temperature can be set.
- Safe and nice:
Automatic timing function, note in the stop bar after 2 hours, machine automatically shut down power, Encountered automatic fault shutdown, can safety, environmental protection, energy saving effect.
- General supplies:
users can adjust by setting the temperature of hot pressing to meet the different use of paper tape.
- Package:
Packing size: 310*245*275/PC
Groos Weight: 7KG
|
Packing size: 510*310*300/2PC
Groos Weight: 14KG
|
- Product parameters
Bundle note range: RMB notes and national bank note can be applied
Binding speed: ≤ 1.5 seconds/once
Power: AC100V-240/47-63Hz
Standby power: <10W, Max power:<60W
Noise: <70DB weight:6kg
Paper wide: 20mm
Dimensions: 240*200*220mm
Fast operate
- Install paper note:
The superstructure of the machine open, bind tape sets as
Shown in column 3 of the lateral direction, leads to take the lead,
This time pay attention to the direction with the installation
Disk to comply with case cited above diagram.
- Power supply:
Access to power and press the power switch to ON position, the
Machine automatically enters the working state.
- Cover tape:
Will take the lead through the guide wheel A, without paper detection sensor, by passing the lateral guide rollers B.C and loaded by the guide rollers into the band mouth, pressing the enter key then automatically finished the actions.
- Bind:
Put the notes will be counted into the work position, the closely
Aligns the left side of the pressure plate notes, notes contact with the front baffle with the limit, photoelectric switch sensor to the notes already in place, the control system automatically binding action.
- Complete:
When the band heard the collection, Adjacency voice prompt action to
Complete, remove the tie a good note, the end of a bundle
- ON/OFF:
This machine has automatic and manual shutdown functions.
Automatic shutdown: This machine has a automatic shutdown function,
If the stop operation time interval of more than set off, the system
Will automatically cut off power supply, automatic shutdown
- Manual shutdown:
Users can use the power switches on or off
Long time do not unplug the power cord.
- Setup and Resize
Debug Method: press the "Clear" button waiting for Temperature to 00
- Temperature=00 is tightness adjustment: (Factory value=30)
Press "Enter paper" button the into the set state, now press "+ - " button,
Enter the required values, press "Enter paper" button again, Setting out the state , press
"Quit paper" button, set item switch.
- Temperature = 01 is feed length adjustment: (Factory value=3) press "+ - " button,
Input the required values, press " quit paper " button, set the project into the next.
- Temperature = 02 is sensitivity adjustment: (Factory value = 9) Press "Enter paper "
Button then into the set state, now press "+ - " button. Enter the required values, press "Enter paper " button again, setting out the state, press "Quit paper" button, Set item switch
- Temperature=03 is Temperature sensor compensation value: ( Factory value=0 ) press
" Enter paper " button then into the set state, now press " Enter paper " button then into the set state, now press "+ - " button, enter the required values, press "Enter paper "
Button again, setting out the state. Press "Quit paper " button, set item switch
- Temperature=04 is sensor detection threshold value paperless: ( Factory value=30 ) press r " Enter paper " button then into the set state, now press "+ - " button, enter the required values, press " Quit paper " button, Set item switch
- Temperature=05 is set off time: (Factory value=60)press "Enter paper" button then into the set state, now press "+ -" button, enter the required values, press "Enter paper" button again. Setting out the state, press "Quit paper" button, set item switch.
- Temperature=06 is Operation mode setting: ( Factory value=0 )
Press "Enter paper" button then into the set state, now press
" + - " button, enter the required values, press "Enter paper"
button again, setting out the state, press "Quit paper" button , Set itmes switch
| | | | |